1982 Ford Timken Parts


Showing 1 - 10 of 10 products
Image
SKU
Product
Rating
Price

Timken
  • Tapered Roller Bearing Cone and Cup Assembly
  • Tremec 140, 141
  • Both the inner (cone) and outer (cup) should be replaced at the same time to maximize reliability and life
  • Suggested Purchase Quantity: 2
    • Most jobs typically require 2 of this item.

Additional Fitment Information:
Vehicle Trans Type Transmission Position Trans. Speed
1982 - Ford Mustang Transmission Manual Rear 5

Timken
  • Tapered Roller Bearing Cone and Cup Assembly
  • Tremec 140, 141
  • Both the inner (cone) and outer (cup) should be replaced at the same time to maximize reliability and life
  • Suggested Purchase Quantity: 2
    • Most jobs typically require 2 of this item.

Additional Fitment Information:
Vehicle Trans Type Transmission Position Trans. Speed
1982 - Ford Mustang Transmission Manual Front 5

Timken
  • Grease/Oil Seal
  • 9 in. Ring Gear
  • Vent holes allow lubricants to flow freely around the seal lip - cooling seal components and removing heat build-up
  • Suggested Purchase Quantity: 2
    • Most jobs typically require 2 of this item.

Additional Fitment Information:
Vehicle Position Drive Type
1982 - Ford Bronco Rear 4WD

Timken
  • Grease/Oil Seal
  • 3,750 lb. Axle
  • Vent holes allow lubricants to flow freely around the seal lip - cooling seal components and removing heat build-up
  • Suggested Purchase Quantity: 2
    • Most jobs typically require 2 of this item.

Additional Fitment Information:
Vehicle Position Drive Type
1982 - Ford E-150 Econoline Rear RWD

Timken
  • Grease/Oil Seal
  • 3,750 lb. Axle - 9 in. Ring Gear
  • Vent holes allow lubricants to flow freely around the seal lip - cooling seal components and removing heat build-up
  • Suggested Purchase Quantity: 2
    • Most jobs typically require 2 of this item.

Additional Fitment Information:
Vehicle Position Drive Type
1982 - Ford F-150 Rear RWD

Timken
  • Grease/Oil Seal
  • 3,300 lb. Axle - Tapered Bearing
  • Vent holes allow lubricants to flow freely around the seal lip - cooling seal components and removing heat build-up
  • Suggested Purchase Quantity: 2
    • Most jobs typically require 2 of this item.

Additional Fitment Information:
Vehicle Position Drive Type
1982 - Ford F-150 Rear RWD

Timken
  • This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.

Additional Fitment Information:
Vehicle Block CC Position Engine CID
1982 - Ford F-150 V 5753 Rear 8 Cyl 5.8L 351

Timken
  • Tapered Roller Bearing Cone and Cup Assembly
  • From Chassis Number F30002
  • Both the inner (cone) and outer (cup) should be replaced at the same time to maximize reliability and life
  • Suggested Purchase Quantity: 2
    • Most jobs typically require 2 of this item.

Additional Fitment Information:
Vehicle Position Drive Type
1982 - Ford Bronco Front Inner 4WD

Timken
  • Tapered Roller Bearing Cone and Cup Assembly
  • From Chassis Number F70001
  • Both the inner (cone) and outer (cup) should be replaced at the same time to maximize reliability and life
  • Suggested Purchase Quantity: 2
    • Most jobs typically require 2 of this item.

Additional Fitment Information:
Vehicle Position Drive Type
1982 - Ford F-150 Front Inner 4WD

Timken
  • Tapered Roller Bearing Cone and Cup Assembly
  • Dana/Spicer 44 Axle
  • Both the inner (cone) and outer (cup) should be replaced at the same time to maximize reliability and life
  • Suggested Purchase Quantity: 2
    • Most jobs typically require 2 of this item.

Additional Fitment Information:
Vehicle Position Drive Type
1982 - Ford F-250 Front Inner 4WD
Showing 1 - 10 of 10 products

Loading...